Filter
Showing 161–180 of 212 resultsSorted by latest
Sort:
Show:
| Parameter | Details (Standard - TJ 2400) | Details (Low-Viscosity - TJ 2404) |
|---|---|---|
| Model | GHEXA-MNT-CON-ACR-016 | GHEXA-MNT-CON-ACR-016 |
| Material Type | UV-Curing Acrylic Resin (Single-Component) | UV-Curing Acrylic Resin (Single-Component) |
| Curing Method | Low-energy UV light | Low-energy UV light |
| Curing Time | 30-60 seconds | Approximately 2 minutes |
| Exotherm / Heat Release | Very low | Very low |
| Viscosity | Medium | Low (enhanced flowability) |
| Appearance after Cure | High transparency / crystal clear | High transparency / crystal clear |
| Hardness (Shore D, typical) | ~78-82 | ~78-82 |
| Shrinkage Rate | Low | Low |
| Additional Features | Fastest curing for rapid batch prep; minimal heat generation | Superior flow and penetration; ideal for complex shapes or vacuum assist |
| Package Size | 1 kg | 1 kg |
| Parameter | Details |
|---|---|
| Model | GHEXA-MNT-CON-EPO-015 |
| Material Type | Conductive Epoxy Resin (Cold Mounting) |
| Components | Part A: Conductive Epoxy Resin (Liquid), Part B: Hardener (Liquid) |
| Mixing Ratio (A:B w/w) | 2:1 |
| Mixing Time | 5-10 minutes |
| Curing Time (at 25°C) | 2-3 hours |
| Peak Exotherm Temperature | 90°C |
| Hardness (Shore D) | 82 |
| Appearance | Colorless and transparent (with conductive properties) |
| Edge Retention | Excellent |
| Shrinkage Rate | Very low |
| Additional Features | Electrically conductive for SEM/EDS use; superior flowability, strong adhesion, high chemical resistance; eliminates need for carbon/gold coating on non-conductive samples; suitable for vacuum impregnation |
| Parameter | Details |
|---|---|
| Model | GHEXA-MNT-CON-EPO-014 |
| Material Type | Epoxy Resin (Cold Mounting) |
| Components | Part A: Epoxy Resin (Liquid), Part B: Hardener (Liquid) |
| Mixing Ratio (A:B w/w) | 2:1 |
| Mixing Time | 10-20 minutes |
| Curing Time (at 25°C) | 8-12 hours |
| Peak Exotherm Temperature | 40°C |
| Hardness (Shore D) | 80 |
| Appearance | Colorless and transparent |
| Edge Retention | Better |
| Shrinkage Rate | Very low |
| Additional Features | Excellent flowability, superior adhesion, high chemical resistance and stability; low exotherm for heat-sensitive samples; versatile for both routine and precision mounting |
| Parameter | Details |
|---|---|
| Model | GHEXA-MNT-CON-EPO-013 |
| Material Type | Low-Viscosity Epoxy Resin (Cold Mounting) |
| Components | Part A: Epoxy Resin (Liquid), Part B: Hardener (Liquid) |
| Mixing Ratio (A:B w/w) | 3:1 |
| Pot Life | 30-60 minutes |
| Mixing Time | 3-5 minutes (recommended) |
| Cure Time (at 25°C) | 10-12 hours (full cure) |
| Peak Exotherm Temperature | <32°C |
| Hardness (Shore D) | 80 |
| Appearance | Colorless and transparent |
| Edge Protection | Better |
| Viscosity | Low (excellent flow and penetration) |
| Additional Features | Superior adhesion, very low shrinkage, high chemical resistance; ideal for vacuum impregnation and complex/porous samples |
| Parameter | Details |
|---|---|
| Model | GHEXA-MNT-CON-EPO-012 |
| Material Type | Epoxy Resin (Cold Mounting) |
| Components | Part A: Epoxy Resin (Liquid), Part B: Hardener (Liquid) |
| Mixing Ratio (A:B w/w) | 4.5:1 |
| Mixing Time | 5-10 minutes |
| Curing Time (at 25°C) | 45-90 minutes |
| Peak Exotherm Temperature | 125°C |
| Hardness (Shore D) | 82 |
| Appearance | Colorless and transparent |
| Edge Retention | Excellent |
| Shrinkage Rate | Very low |
| Additional Features | Superior flowability, strong adhesion, high chemical resistance and stability; suitable for vacuum impregnation when maximum clarity and void-free embedding are required |
| Parameter | Specification |
|---|---|
| Model | GHEXA-GRP-EQP-AUT-002 |
| Power Supply | AC 220V / 50 Hz + Ground; Total Power: 7 kW, Rated Power: 2 kW |
| Compressed Air | 0.6–0.7 MPa, Hose OD Φ10 mm |
| External Water Supply | <0.3 MPa, Pipe OD Φ10 mm |
| Drainage | Drain Pipe OD 32 mm |
| Sample Mounting Box Sizes | 39×47×12 mm / 30×27×12 mm; Max Quantity: 21 |
| Alignment System | 25 Megapixel CCD Camera; Field of View: 35×35 mm; Grinding Precision: ±10 μm |
| Laser Marking/Reading | Yes; Max Number of Lines: 30; Line Drawing: Specified distance translation |
| Grinding/Polishing Stations | 2 Stations; Disc Diameter: Φ254 mm; Rotation Speed: 100–1000 rpm; Motor: 1 kW |
| Grinding Head | Holds 3 Samples; Motor: 0.4 kW; Speed: 0–360° reciprocating swing; Pressure: 5–100 N |
| Dispensing System | 4 Groups × 1.8 L each; Flow Rate: 0–50 ml/min; Mechanical Stirring: 2 Groups; Liquid Level Alert: Yes |
| Disc Storage | 20 Grinding/Polishing Discs; Disc Life Alert: Usage count or force-based |
| Cleaning Station | Water Rinse + Ultrasonic + High-Speed Spin-Dry + Independent Air Blow-Dry |
| Control System | PLC + 15-inch Main Screen + 7-inch Auxiliary Screen; Dual 24-inch Computer Displays |
| Safety Features | Emergency Stop, Safety Door Lock (PLd level), Three-Color Alarm Light |
| Program Library | 30 Program Groups; Max 10 Steps per Program; End Conditions: Remaining/Grind Amount (min 0.001 mm) or Time |
| Grinding Modes | By Pressure (0–100 N) or Speed (min 0.001 mm/s) |
| Sample Output | Face-up, orderly arranged in recovery tray to prevent surface scratching |
| Dimensions (Screen & Light Folded) | 2400 × 1320 × 2000 mm |
| Weight | 1500 kg |
| Parameter | Specification |
|---|---|
| Product Model | GHEXA-MNT-CON-EPO-011 |
| Material Type | Epoxy Resin Mounting Compound |
| System | Two-Part (Liquid Resin + Liquid Hardener) |
| Appearance | Colorless, transparent |
| Part A | Epoxy Resin, Liquid |
| Part B | Hardener, Liquid |
| Mixing Ratio (A:B, w/w) | 2 : 1 |
| Mixing Time | 5–10 minutes |
| Curing Time @ 25 °C | 1–2 hours |
| Peak Exothermic Temperature | 112 °C |
| Hardness | Shore D 78 |
| Edge Retention | Good |
| Flowability | Excellent |
| Shrinkage | Low |
| Adhesion | Strong |
| Chemical Stability | Superior |
| Mold Reference | Φ30 mm mold at 20–25 °C |
| Solvent Compatibility | Cured resin removable with Trojan DSV10 solvent |
| Parameter | Specification |
|---|---|
| Product Model | GHEXA-MNT-CON-EPO-010 |
| Material Type | Epoxy Resin Mounting Compound |
| System | Two-Part (Liquid Resin + Liquid Hardener) |
| Appearance | Colorless transparent to light yellow |
| Part A | Epoxy Resin, Liquid |
| Part B | Hardener, Liquid |
| Mixing Ratio (A:B, w/w) | 2 : 1 |
| Mixing Time | 4–8 minutes |
| Curing Time @ 25 °C | 30–60 minutes |
| Peak Exothermic Temperature | 144 °C |
| Hardness | Shore D 82 |
| Edge Retention | Better / Enhanced |
| Flowability | Excellent |
| Shrinkage | Low |
| Adhesion | Strong |
| Chemical Stability | Superior |
| Transparency | High |
| Parameter | Specification |
|---|---|
| Product Model | GHEXA-MNT-CON-ACR-009 |
| Material Type | Acrylic Resin Mounting Compound |
| System | Two-Part (Resin + Hardener) |
| Appearance | Semi-transparent |
| Part A | Resin, Powder (White) |
| Part B | Hardener, Liquid |
| Mixing Ratio (A:B, w/w) | 10 : 5 |
| Mixing Time | 2–4 minutes |
| Curing Time @ 25 °C | 8–10 minutes |
| Peak Exothermic Temperature | 85 °C |
| Hardness | Shore D 82 |
| Edge Retention | Better / Enhanced |
| Shrinkage Rate | Low |
| Permeability | Good |
| Recommended Process | Cold mounting press |
| Mold Reference | Φ30 mm mold at 20–25 °C |
| Solvent Compatibility | Can be dissolved with Trojan DSV10 solvent after curing |
| Parameter | Specification |
|---|---|
| Product Model | GHEXA-MNT-CON-ACR-008 |
| Material Type | Acrylic Resin Mounting Compound |
| System | Two-Part (Resin + Hardener) |
| Part A | Resin, Powder (White) |
| Part B | Hardener, Liquid |
| Mixing Ratio (A:B, w/w) | 10 : 8 |
| Mixing Time | 2–4 minutes |
| Curing Time @ 25 °C | 8–10 minutes |
| Peak Exothermic Temperature | 80 °C |
| Hardness | Shore D 80 |
| Transparency | High |
| Flowability | Excellent |
| Permeability | Excellent |
| Edge Protection | Good |
| Typical Use | Rapid embedding & mounting |
| Parameter | Specification |
|---|---|
| Model | GHEXA-CUT-ACC-009 |
| Applicable Machines | GHEXA-CUT-EQP-AUTO-002 (automatic), GHEXA-CUT-EQP-MAN-007 (manual) |
| Primary Application | Large & heavy sample vertical clamping |
| Arm Unloading Range | 90 mm |
| Clamping Height Range | -20 mm to 90 mm |
| Clamping Force | 1600 N |
| Mounting Type | Threaded T-slot block (M10) |
| Order No. | 23.01.180H400 |
| Material | High-strength hardened steel with corrosion-resistant coating |
| Clamping Mechanism | Vertical downward pressure arm with high-force adjustment |
| Compatibility Note | Optimized for large-chamber cutting machines with extended worktables and side-door access |
| Parameter | Specification |
|---|---|
| Model | GHEXA-CUT-ACC-008 |
| Applicable Machines | GHEXA-CUT-EQP-MAN-006 (manual abrasive sectioning machine) |
| Primary Application | Small sample vertical clamping |
| Arm Unloading Range | 60 mm |
| Clamping Height Range | -15 mm to 80 mm |
| Clamping Force | 160 N |
| Mounting Type | Threaded T-slot block (M6) |
| Order No. | 23.01.290H200 |
| Material | Hardened steel with corrosion-resistant finish |
| Clamping Mechanism | Vertical downward pressure arm with adjustable height and controlled force |
| Compatibility Note | Ideal for small-chamber manual cutters; supports vertical fixturing of thin/fragile samples |
| Parameter | Specification |
|---|---|
| Model | GHEXA-CUT-ACC-007 |
| Applicable Machines | GHEXA-CUT-EQP-MAN-006 (manual abrasive sectioning machine) |
| Primary Application | Small sample parallel/outward clamping |
| Jaw Width | 65 mm |
| Jaw Opening / Travel Range | 28 mm |
| Mounting Type | Threaded T-slot block (M6) |
| Order No. | 23.01.300X200 |
| Material | Precision-machined hardened steel with corrosion-resistant finish |
| Clamping Mechanism | Paralleled adjustment for uniform, even pressure distribution |
| Compatibility Note | Designed for small-chamber manual cutters; excels at clamping flat or multi-layered small specimens |
| Parameter | Specification |
|---|---|
| Model | GHEXA-CUT-ACC-006 |
| Applicable Machines | GHEXA-CUT-EQP-MAN-006 (manual abrasive sectioning machine) |
| Primary Application | Small & delicate sample splitting/clamping |
| Jaw Width | 30 mm |
| Jaw Opening / Travel Range | 45 mm |
| Mounting Type | Threaded T-slot block (M6) |
| Order No. | 23.01.305D200 |
| Material | High-precision hardened steel with corrosion-resistant finish |
| Clamping Mechanism | Manual adjustment with fine-thread control for gentle, uniform pressure |
| Compatibility Note | Optimized for small-chamber manual cutters; ideal for side-by-side or serial small sample processing |
| Parameter | Value |
|---|---|
| Product Name | Epoxy Resin (10:1 Fast-Cure System) |
| Model | GHEXA-MNT-CON-EPO-007 |
| Type | Two-component epoxy (Resin A + Hardener B) |
| Mixing Ratio | 10:1 by volume (Resin : Hardener) |
| Curing Conditions | 5 minutes at 150°C |
| Curing Characteristic | Bubble-free cure; turns red upon full cure |
| Appearance (Uncured) | Clear to pale yellow liquid (Resin); clear liquid (Hardener) |
| Appearance (Cured) | Red solid |
| Chemical Resistance | Excellent – resists most chemical etchants after curing |
| Adhesion | Superior to metals, ceramics, glass, most plastics |
| Application Method | Brush, pipette, or dispensing needle |
| Primary Uses | Delicate specimen bonding, TEM stacking, pre-coating, PCB micro-hole filling |
| Parameter | Value |
|---|---|
| Product Name | Mineral-Filled Edge Retention Hot Mounting Resin |
| Model | GHEXA-MNT-CON-PHE-006 |
| Base Material | Mineral-filled melamine resin |
| Appearance | Light Yellow Particles and White Powder |
| Holding Time | 4-7 min |
| Cooling Time | 5-8 min |
| Cooling Rate | Medium |
| Heating Pressure | 150-300 bar |
| Heating Temperature | 150-180°C |
| Hardness (Shore D) | 92-95 |
| Key Features | High hardness, excellent edge retention, good adhesion, superior grinding & polishing performance |
| Primary Applications | Medium-hard materials (e.g., steels, hard alloys, aluminum, copper) |
| Parameter | Specification |
|---|---|
| Model | GHEXA-CUT-ACC-005 |
| Applicable Machines | GHEXA-CUT-EQP-MAN-007 (manual abrasive sectioning machine) |
| Primary Application | Large & heavy sample clamping |
| Jaw Dimensions (W × H) | 80 × 70 mm |
| Jaw Opening / Travel Range | 90 mm |
| Mounting Type | Threaded T-slot blocks (M10) |
| Left-Side Variant Order No. | 23.01.150S300L |
| Right-Side Variant Order No. | 23.01.160S300R |
| Clamping Mechanism | Handlebar-style fast-lock quick-release for one-handed operation |
| Material | High-strength hardened steel with corrosion-resistant finish |
| Compatibility Note | Optimized for manual cutting machines with spacious worktables and side-door access |
| Parameter | Value |
|---|---|
| Product Type | Conductive Hot Mounting Resin |
| Appearance | Dark Brown Particles and Powder |
| Filler | Conductive (Carbon-based) |
| Holding Time | 4-6 min |
| Cooling Time | 4-6 min |
| Cooling Rate | High |
| Heating Pressure | 150-250 bar |
| Heating Temperature | 150-180 °C |
| Hardness (Shore D) | 90-92 |
| Parameter | Value |
|---|---|
| Product Type | Epoxy Edge Retention Hot Mounting Resin |
| Appearance | Black Particles (Grit) |
| Filler | Glass Fiber |
| Holding Time | 5-7 min |
| Cooling Time | 4-6 min |
| Cooling Rate | Medium |
| Heating Pressure | 150-300 bar |
| Heating Temperature | 150-180 °C |
| Hardness (Shore D) | 90-93 |
| Parameter | Specification |
|---|---|
| Model | GHEXA-MNT-EQP-HOT-002 |
| Power Supply | 220 V, 1-phase, 4.5 kW, 30 A |
| Heating Power | 4.0 kW (adjustable 10–100%) |
| Heating Control | Power adjustable; real-time temperature & pressure display |
| Heating Range | 100–200 °C |
| Holding Time | 0–99 minutes |
| Pressure Range | 0–500 Bar (depending on cylinder size) |
| Heating Method | Surrounded (uniform radial heating) |
| Sample Size (Mold Diameter) | Φ30 mm (standard); optional Φ25.4, Φ32, Φ40, Φ50 mm |
| Cooling Method | Automatic (by time or temperature endpoint); manual override |
| Cooling Rate | High, medium, low selectable |
| Control Interface | 7-inch touchscreen with user-friendly operation |
| Status Indication | LED light strip for operating status |
| Safety & Operation | Sliding cover for safe & easy access, low operating noise |
| Water Connections | Inlet: OD Φ8 mm connector, pressure <0.3 MPa Outlet: OD Φ12 mm connector |
| Operating Environment | Temperature: -20 °C to 60 °C Humidity: 0–95% RH |
| Dimensions (W×D×H) | 657 × 509 × 548 mm |
| Weight | 70 kg |
| Additional Features | Real-time temperature/pressure variation display, storage for multiple operation parameter sets, optional circulating water tank support, compact design with low noise |
Recently viewed items
| Parameter | Value |
|---|---|
| Product Name | Microscope |
| Model | GHEXA-11.1521-T |
| Head | Trinocular, 360° rotatable, 30° inclined, interpupillary distance adjustable |
| Eyepieces | Wide Field WF10x/16mm (pair) |
| Nosepiece | Quadruple, reversed ball-bearing |
| Objectives | Achromatic 4x, 10x, 40x (spring), 100x (spring, oil immersion) |
| Stage | Double-layer mechanical stage 115×125 mm with coaxial coarse & fine focus, right-hand low-position controls |
| Focusing | Coaxial coarse & fine focusing knobs, coarse stroke 22 mm, fine stroke 0.002 mm per rotation, tension adjustable, upper limit stop |
| Condenser | Abbe N.A. 1.25 with iris diaphragm and filter holder |
| Illumination | 6V/20W Halogen (with intensity control) or LED (interchangeable) |
| Camera Port | Built-in 1x C-Mount adapter |
| Power Supply | 100–240V AC, 50/60 Hz |
| Packaging | 2 pcs per carton, dimensions 45×27×41 cm, gross/net weight 7.5/6.5 kg |
